Assembly and Device Care

Assemble the Birdfy Feeder

Align the protrusions on either side of the roof with the notches on the bird seed container. Push the roof downward until you hear a clicking sound indicating a secure fit.
Rotate the roof to buckle it onto the back of the container. Ensure that it is snug and stable.
Using the provided perch screw, attach the perch by screwing it into the designated hole, making sure that the groove is facing downward.

Note: It is important to properly install the perch as described to keep the perch fixed and to avoid seed accumulation in the groove.

Align the protrusions on either side of the roof with the notches on the bird seed container. Push the roof downward until you hear a clicking sound indicating a secure fit.
Rotate the roof to buckle it onto the back of the container. Ensure that it is snug and stable.
Screw the antenna onto the back of the feeder.
Attach the mounting bracket to the bottom of the feeder with the provided thumbscrew.
Attach the perch by screwing it into the designated hole.

Use the provided drill template to mark the locations of the holes, then use an electric drill (15/64", 6mm) to drill two holes.
Drive the provided plastic anchors into the holes. Skip this step if you are mounting on wood. Then drive in the mounting screws.
Install the mounting bracket onto your wall using the screws provided. Make sure it is level and secure.
Finally, slide the Birdfy Feeder into the bracket through the slide rail.

Use the provided drill template to mark the locations of the holes, then use an electric drill (15/64", 6mm) to drill two holes.
Drive the provided plastic anchors into the holes. Skip this step if you are mounting on wood. Next, fasten the hanging bracket on the wall using the screws.
Hang the feeder onto the wall.

Loosen the provided hose clip by turning the handle counterclockwise.
Align the mounting bracket with the pole and wrap the hose clip around both the bracket and the pole. Make sure the bracket is level and secure.
Tighten the hose clip by turning the handle clockwise until it is snugly in place.
Slide the Birdfy Feeder into the bracket through the slide rail.

Turn the antenna 90 degrees sideways to avoid damaging it. Unbuckle the roof of your Birdfy Feeder and lift it up until it detaches.
Remove the perch by unscrewing the perch screw in a counter-clockwise direction.
Find the screw for the feeding tray at the back of the feeder body, just below the charging port. Unscrew it in a counter-clockwise direction and take off the feeding tray.
Clean the roof, perch, and feeding tray with a brush and soapy water.
Use a long-handled brush to scrub the inside of the bird seed bin. Make sure that the silicone covers on the charging ports are securely sealed to prevent water from getting into the camera.
Dry your Birdfy Feeder thoroughly before reassembling and using it.

Unscrew the antenna. Unbuckle the roof of your Birdfy Feeder and lift it up until it detaches.
Remove the perch by unscrewing the perch screw in a counter-clockwise direction.
Clean the roof, perch, and feeder body with a brush and soapy water.
Use a long-handled brush to scrub the inside of the bird seed bin. Make sure that the silicone covers on the charging ports are securely sealed to prevent water from getting into the camera.
Dry your Birdfy Feeder thoroughly before reassembling and using it.

While your Birdfy Feeder is mounted on a wall or a tree, turn the feeder body around.
Open the roof and fill the feeder with birdseed. Then turn back the feeder.

Here are two ways to secure your Birdfy Feeder antenna and protect it from potential damage caused by squirrels, raccoons, and other wildlife:

Take a zip tie and thread the end that looks like an actual tie through the square notch on the back of the tie. Tighten it slightly to create a large circle.
Unbuckle the roof of the feeder and loop the zip tie around the antenna, placing it on the protrusion on the back of the feeder body. Rotate the roof back into place and buckle it up.
Tighten the zip tie to ensure a secure fit.

Apply an adhesive mount to the back of the feeder body.
Buckle up the roof of the feeder.
Take a zip tie and circle it around the antenna and through the mount. Tighten the zip tie to create a secure fit.

Remove the original perch by turning the perch screw counter-clockwise.
Align the hole on the inner side of the Hummee Extension with the screw hole on the feeder base. Push the extension in firmly until it clicks into place.
To disassemble it, lift the buckles on both ends of the Hummee Extension and pull it out.

Before removing the bracket, we advise that you take your Birdfy Feeder down from its mounted position.
Locate the pull tab on the bracket. Use the fleshy part of your fingertip to press firmly into the tab, then apply enough force with your entire arm to pull it outward until it is completely removed from the feeder.
Remember to use the fleshy part of your fingertip to press down on the pull tab, or else you may hurt your nails.

Before removing the bracket, we advise that you take your Birdfy Feeder down from its mounted position.
Put the feeder down on a flat surface and unscrew the bracket.